MikMek SubMicro Manual de usuario descargar pdf (Pagina 51)

The following is an overview of what each Menu option does:

BAUD RATE?

Controls the serial interface baud rate, parity bit, data bits and stop bits.

Here are the following choices:

MINI/MICRO?

Defines the type of printer

MINI Is for a printer with a Silent Cutter Assembly (SC2) (Mini, Mini Plus, Mini MB, Dual Mini)

MICRO Is for a printer without a SC2 (Micro, Micro Plus, Micro MB, Dual Micro)

PRINT SPEED?

Controls the speed the ticket travels at. Also effects the print quality.

The numbers range from 0 - FASTEST to 7 - SLOWEST. 3 is factory default.

DIAGNOSTIC MODE?

Please consult your Programming Guide

Your choices are YES or NO. NO is factory default.

TICKET TYPE?

Defines how the optos are configured on the paper guide assembly.

Here are the following choices:

NORMAL

Both optos are inline with each other (usually mounted on a black bracket)

ATM

Feed opto is mounted under the thermal head and cut opto is attached to the cutter assy.

LABEL

Same as ATM but the cut opto is a see through type.

SPECIAL TICKET

This option is for a Micro MB or a printer with a ticket load switch

STATUS ENABLED?

Sets status response protocols.

Here are the following choices:

NONE

Disables the XON/XOFF and status response protocols

SERIAL

Enables the XON/XOFF and status response protocol for the serial port.

PARALLEL

Enables bi

directional parallel status responses if printer is configured as bi

directional.

SER/PAR

Enables both bi-directional parallel and serial status responses.

USB

Enables USB status responses

USB/SER

Enables USB and serial status responses

USB/PAR

Enables USB and bi-directional parallel

USB/SER/PAR

Enables USB, bi-directional parallel and serial status responses

TRANSPARENT MODE?

Please consult your Programming Guide

Your choices are YES (Enabled) or NO (Disabled).

PAPER MODE?

Is generally used only for test purposes. It may also be used on roll stock with no

black marks on the ticket. Your choices are YES (Enabled) or NO (Disabled). NO is factory default.

HEAD DPI?

Defines thermal head dpi (dots per inch) - choices are 200, 300 or 600.

This feature is set at the factory and should not be changed.

SPECIAL HEAD?

Is used when a special paper path size is installed (2.125”, 2.5”, 2.7”….)

Here are the following choices: This feature is set at the factory.

NO No special head

ON P1

DUAL & SINGLE PATH PRINTER ONLY (fixed path)

ON P2

DUAL PATH PRINTER ONLY on path #2 (fixed path)

ON BOTH

DUAL PATH PRINTER ONLY on both paths (fixed path)

REV ADJ2 P1

DUAL & SINGLE PATH PRINTER WITH RADJ paper guide set to 2”

REV ADJ2 P2

DUAL PATH PRINTER WITH RADJ paper guide set to 2” on path #2

REV ADJ2 BOTH

DUAL PATH PRINTER WITH REV RADJ paper guide set to 2” on both paths

REV ADJ2.5 P1

DUAL & SINGLE PATH PRINTER WITH RADJ paper guide set to 2.50”

1200,N,8,1

4800,N,8,1

19200,N,8,1

38400,E,7,1

1200,E,7,1 4800,E,7,1 19200,E,7,1 57600,N,8,1

1200,O,7,1 4800,O,7,1 19200,0,7,1 57600,E,7,1

2400,N,8,1 9600,N,8,1 28800,N,8,1 115200,N,8,1

2400,E,7,1 9600,E,7,1 28800,E,7,1 115200,E,7,1

2400,O,7,1 9600,0,7,1 38400,N,8,1

1 2 ... 46 47 48 49 50 51 52 53 54 55 56 ... 134 135

Comentarios a estos manuales

Sin comentarios

MikMek SubMicro Manual de usuario Pagina 51

Comentarios a estos manuales

Relacionado con productos y manuales para Impresión y escaneo MikMek SubMicro